///DR's Gran Turismo Cockpit DIY (Updated 8/17/10)\\\

I was talking about the 2 boards directly under the seat brackets, the 2 other boards that those are resting on(front and rear) an the fact that those 2 are not directly connected to the risers, which are there for support, no? In the front it looks like the 2 side screws go through the risers and into the added blocks under the seat bracket. But in the rear it looks like it just sits on the 1" lip that the board creates. Doesn't look very sturdy.
So pretty much, it looks like the 2 boards directly under the seat and the 2 boards supporting those, aren't connected to the risers. To me that looked odd as I would think all 4 of the boards should be nailed to the risers.. That's all I was saying.
 
dave_sz
I was talking about the 2 boards directly under the seat brackets, the 2 other boards that those are resting on(front and rear) an the fact that those 2 are not directly connected to the risers, which are there for support, no? In the front it looks like the 2 side screws go through the risers and into the added blocks under the seat bracket. But in the rear it looks like it just sits on the 1" lip that the board creates. Doesn't look very sturdy.
So pretty much, it looks like the 2 boards directly under the seat and the 2 boards supporting those, aren't connected to the risers. To me that looked odd as I would think all 4 of the boards should be nailed to the risers.. That's all I was saying.
Click to expand...

Bro, you should read the post where I have explained all that (3 posts up). Why you are confused is beyond me.

I imagine you're not familiar with woodworking?



;)
 
Delphic Reason
Bro, you should read the post where I have explained all that (3 posts up). Why you are confused is beyond me.

I imagine you're not familiar with woodworking?



;)
Click to expand...

I can understand his concerns for your welfare...

Afterall your/my ancestors did build the Titanic!


R.I.P
 
dave_sz
I was talking about the 2 boards directly under the seat brackets, the 2 other boards that those are resting on(front and rear) an the fact that those 2 are not directly connected to the risers, which are there for support, no? In the front it looks like the 2 side screws go through the risers and into the added blocks under the seat bracket. But in the rear it looks like it just sits on the 1" lip that the board creates. Doesn't look very sturdy.
So pretty much, it looks like the 2 boards directly under the seat and the 2 boards supporting those, aren't connected to the risers. To me that looked odd as I would think all 4 of the boards should be nailed to the risers.. That's all I was saying.
Click to expand...

I think this is where your eyes deceive you dave_sz, those 2 screws don't go through to the block/board under the seat runner. The front on photo clearly shows this. DSC01972.jpg
The block/board is for mounting the runner, notice the rear is just past halfway back. DSC01974.jpg So the front has no more support than the rear.


I hope this is your concern and I have found the explanation. 👍

Hope you don't mind me jumping in DR.
 
Last edited:
Mr Latte
I can understand his concerns for your welfare...

Afterall your/my ancestors did build the Titanic!


R.I.P
Click to expand...

and the Delorean...

You may have a point there...

Although, my cockpit has been designated unsinkable... I mean, it is made of wood.

Hope you don't mind me jumping in DR.
Click to expand...

Not at all. I'll take help wherever I can get it, mate.



;)
 
I am currently doing some testing with the Porsche Carrera Wheel (and Clubsport Paddles), which I will be reviewing very soon. As soon as I am through with testing (with a PWC Giveaway to follow, right here at GTP!) I will get back to work on the cockpit.

I must admit, my eyes keep wandering over to the corner of the room where one of my cockpits sits. My mind goes through what I have left to do, how long it will take, new ideas, etc... So, I am eager to get back to work on it.

First I will finish the writeup (first post) as it currently stands. Then I will get to paneling (which will be added to the first post as well, once finished). After that, it's the BK mount.

Stay tuned!




;)
 
Mr Latte
Okay Ive been tuned now for over a week...

Anything new going on?
Click to expand...

There will be very shortly. I am finally done with some previous engagements. Now I can get back to framing my rig, and shortly after (or before, haven't decided yet) the BK mount.

Some work space is being cleared as we speak.




;)
 
Just checking you wernt slacking, sitting with cold beers every night, hee hee....

Are you for adding electric windows or a sunroof by chance, lol
 
Probably not going to go that far. Although a door like enclosure on one side (solid on the other) is a possibility. First things first, though.

I'll most likely frame first, as I don't have the other part I need for the BK mount, as of yet.



;)
 
Damn this "cockpit" section is getting little chit chat lately but lots of viewers.
Have you anything new happening lately yourself mate?
 
Mr Latte
Damn this "cockpit" section is getting little chit chat lately but lots of viewers.
Have you anything new happening lately yourself mate?
Click to expand...

Nothing much lately, unfortunately. I just haven't had the time. I go back to work soon (no cast anymore, and I'm walking again) so I'll have less time, but with more money. It should balance out rather nicely though. The "more money" part being key.

Nevertheless, I hope to get paneling done on both cockpits soon. At least the uprights.

Currently, I'm waiting for a response from Fanatec regarding a set of pedals that need to be replaced, that belong to a friend of mine, but reside at my house (with the secondary cockpit and wheel).

My standard pedals had a brake sensitivity problem, and they replaced them no questions asked, so I expect the same should apply here. Still, no response after a few days (Thomas usually replies promptly).

We'll see what happens.




;)
 
UPDATE:

The pedals have been replaced (en-route), so I'll be back to work on the cockpit tomorrow (Yay!)

First, structural support, then panels.

Stay tuned...



;)
 
UPDATE:

I added a stabilizer bar to the uprights (i.e between 2 uprights on front of cockpit), to which I attached the front paneling. I will cut a few slits (or some shapes) into the paneling, both on the front and the sides. Behind which I will be installing wire mesh which will provide areas for the blue LED lights to shine through.

Don't worry, I will add pictures tomorrow (when I'm not at work).




;)
 
Here is a little update...

First I added a stabilizer bar between the two front uprights:

2010-06-21112305.jpg

2010-06-21112247.jpg


Then I cut out some paneling (pine) and secured using some small finishing screws. A little sanding here and there, and it now looks like:

2010-06-22120739.jpg

2010-06-22120812.jpg


I also found some wire mesh at work:

2010-06-23095808.jpg

2010-06-23095821.jpg


I will be cutting out some ventilation areas on the front and side paneling. The above mesh will be cut and placed behind.

Some blue LED light bars will be purchased (example below) and placed under the wheel tray:

http://cgi.ebay.com/ebaymotors/BLUE...ptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fAccessories

With the silver mesh cutouts, and black painted frame (coming soon after paneling is finished), the effect should be interesting.

Stay tuned...





;)
 
speedyK
How is the shifter down at the realistic shifter position connected to the wheel?

I'm asking because the cable provided with the shifter set is only 30 cm long, so no way would it reach the wheel.

Quote from the following Fanatec page: "connection cable 0,3 m ".

http://www.fanatec.de/webshop/new_eu/product_info.php?cPath=28&products_id=64&osCsid=92c2899b36d67ae833d12cb29e14bac4
Click to expand...

You use a longer Cable, Fanatec can sell you one, check the longer pedal cable or you can source your own.
 
speedyK
Ok. Thanks :)

Does the "more" info link work for you?
Click to expand...

Can you provide a link? I can't find the link you speak of.


UPDATE:

I have updated the top of the first post with a few pictures of the current state of the build. So, newcomers to this thread don't have to scroll down so far (or read through a lot of pages) to see what the cockpit looks like when completed (or, "near complete" as it currently stands).




;)
 
Last edited:
Good job, can you estimate how many hours of work has been already used to make the wood parts for the cockpit?

Looking nice! 👍
 
Timppaq
Good job, can you estimate how many hours of work has been already used to make the wood parts for the cockpit?

Looking nice! 👍
Click to expand...

If I had all the wood at one time, and could just focus on building without distractions, it could easily be built in an afternoon, or over a weekend.

My problem (like many who have built cockpits) is I have made a lot of changes over the course of the build, and had plenty of distractions as well.

With all the parts, design, and tools at hand, it would be a quick build.




;)
 
Delphic Reason
If I had all the wood at one time, and could just focus on building without distractions, it could easily be built in an afternoon, or over a weekend.

My problem (like many who have built cockpits) is I have made a lot of changes over the course of the build, and had plenty of distractions as well.

With all the parts, design, and tools at hand, it would be a quick build.

;)
Click to expand...

I mean, all you have to do is screw a few screws into 2 pieces of wood and your done :)

But so is building a house with some added electrical and glass haha
 
slogt
I mean, all you have to do is screw a few screws into 2 pieces of wood and your done :)

But so is building a house with some added electrical and glass haha
Click to expand...

There's always more to a build than meets the eye. Yet, this build is quite rudimentary with regards to difficulty, and tools needed.

Only 4 types of boards and 2 types of screws for the whole build (not counting Inverted Pedal Mount, directions will be up for that soon).



;)
 

Similar threads

super_gt
Fanatec ClubSport Cockpit Formula
Replies
3
Views
4K
i386
I
TheNormsk
RCP Cockpit Sport vs Pro
Replies
0
Views
4K
TheNormsk
TheNormsk
fourthstreet
Fourthstreet’s DIY Sim Racing Cockpit
Replies
7
Views
5K
fourthstreet
fourthstreet
Gorefast
Cockpit Upgrade: Fanatec DD Pro (8nm) & GT Omega ART
Replies
1
Views
3K
Veinz
Veinz
B
Ps5 + VR3 + Logitech G Pro Wheel/Pedals
Replies
18
Views
8K
Monkey Man
Monkey Man

Latest Posts

Back