Fanatec Announcements: CSW V2 Reviews Out
- Thread starter Crispy
- 13,388 comments
- 1,336,763 views
- 2,858
- Australia
- 2,801
- fatkrakr
I think I am going to have to send other email for support. 
My wheel keeps losing center. Not by much 7 to the right in wheel profile is the worse its been. It normally ony goes off by 3, but if I hit a wall or something it will go off to 7. Is that the pcb going bad or something else?
My wheel keeps losing center. Not by much 7 to the right in wheel profile is the worse its been. It normally ony goes off by 3, but if I hit a wall or something it will go off to 7. Is that the pcb going bad or something else?
- 606
I think I am going to have to send other email for support.
what fanatec wheel have you got because my pwts has done that since day1, i think it optical sensor related as when i changed that it dissapeared, however it did come back a couple of times after a month or so, im fairly sure that after time i will be back to square one.
- 1,603
- IN
- Eric_J2358
Double check your wheel mounting bolts inside the QR adapter on both the wheel and the base. If they are loose it could make your center move a tiny bit from the slop in the bolt holes. If those are good, check the position sensor inside the wheel to see if it has loosened. If you've still found nothing after that you'll have to contact Fanatec.
- 2,801
- fatkrakr
Ok thanks. I know its not inside the quick release I check them pretty regular. Ill have to give the position sensor a look. I assume Ill be able to tell what it is easy enough. Just look for something pointed at the code wheel and check if its tight.
No luck with it just being something loose. Sent off a email.
Last edited:
- 2,858
- Australia
Not sure if you Elite guys are aware of one production/design quirk. Was talked about here:
https://www.gtplanet.net/forum/showthread.php?p=8281917
Not sure if it is relevant to the final product, but worth checking.
- 449
- Toronto
- SignsOfChaos
- SignsOfChaos
I wouldn't say that's a quirk with the Formula rim but a quirk with the Elite. I never even noticed that the collar on the Elite was threaded as well.....that's an odd choice made there as usually this type of assembly method would have a tight tolerance unthreaded hole for the bolt to pass through into the threaded holes of the receiver on the rim.
With that said mine went together with no problems. I think it's imperative that when people assemble their Formula rim on their Elite base to assemble it as I did. I noticed when I first assembled it that if I tightened the 1st bolt the 2nd felt like it wasn't going in properly so I immediately stopped....backed it out and then loosened the 1st bolt quite a bit. I then went back and installed the second bolt and it went in with no problem and then I alternated between the two as I tightened them down until both were snugged down. But I can definitely see how some people could have some problems if they're not careful.
The rim though is certainly awesome. The build quality befits the quality of the Elite base SO much better than the stock rim. Everything about it is far better....all the buttons, the metal construction, the joysticks, the paddles (VERY good), LED display, the leather grips feel very good and are super comfy, even the mounting collar is better as its a CNC machined piece vs the cast one on the stock rim. And it's very light.....it doesn't feel a whole lot heavier than the stock rim at all
With that said mine went together with no problems. I think it's imperative that when people assemble their Formula rim on their Elite base to assemble it as I did. I noticed when I first assembled it that if I tightened the 1st bolt the 2nd felt like it wasn't going in properly so I immediately stopped....backed it out and then loosened the 1st bolt quite a bit. I then went back and installed the second bolt and it went in with no problem and then I alternated between the two as I tightened them down until both were snugged down. But I can definitely see how some people could have some problems if they're not careful.
The rim though is certainly awesome. The build quality befits the quality of the Elite base SO much better than the stock rim. Everything about it is far better....all the buttons, the metal construction, the joysticks, the paddles (VERY good), LED display, the leather grips feel very good and are super comfy, even the mounting collar is better as its a CNC machined piece vs the cast one on the stock rim. And it's very light.....it doesn't feel a whole lot heavier than the stock rim at all
JogoAsobi
Premium
- 2,578
Very pretty, but if used on a PS3 with GT5 the same probably applies to the comments about GT6:
From the Developer Interview section of the SimHQ Motorsports E3 2013 Recap: Part 1 - GranTurismo 6
= probably not getting your $ worth, unless you do Forza 4 or PC sims.
Last edited:
- 2,858
- Australia
Oh yeah, the issue certainly lies with the base. I just quoted the picture to help grab the attention of Elite owners.
Reading your thoughts on the new rim, I began to wonder..... Is there any chance that someone might consider fashioning an addition to the formula rim to "circlify" it? May kill a few birds with one stone to be able to switch back and forth between gt and formula set up, using only the formula rim. I am sure it could be done, and the original CSR rims were hardly well respected.
Reading your thoughts on the new rim, I began to wonder..... Is there any chance that someone might consider fashioning an addition to the formula rim to "circlify" it? May kill a few birds with one stone to be able to switch back and forth between gt and formula set up, using only the formula rim. I am sure it could be done, and the original CSR rims were hardly well respected.
- 672
- Toulouse
- TheHBK
- HBK Live
Fanatec "PS3 mode" actually is a G25 emulation mode. So as long as the game supports G25 wheels, Fanatec wheels should work as a G25.
Having native Fanatec support (i.e. Fanatec "PC mode") would be nice as some of the Fanatec wheels features (such as wheel vibration motors) cannot be used in "PS3 mode" (as G25 wheels have no such motors, obviously).
But Fanatec wheels already work wonders in GT5 and will probably still work wonders in GT6 as long as PD doesn't try to detect that you are not using a legacy G25 but a Fanatec wheel in G25 emulation mode instead, in order to try to lock them out or something like that.
Last edited:
- 2,801
- fatkrakr
I was thinking about fanatec and using logitech emulation. For the ps4 wheel makers need to submit drivers for their wheels. Logitech is out of the console market. Does this mean no drivers for the ps4? If so then that will also mean no fanatec wheels on the ps4 along with logitech wheels, unless fanatec finally get their own ps4 drivers.
LogiForce
Premium
- 4,078
- Groningen, Netherlands
- LogiForce86
- LogiForce
- 1,002
- Northern VA
Hawk, where was the shim in your package? I don't remember seeing one with mine. I'll have to make sure to reuse the existing shim.
Now, regarding the new Formula Rim itself: hoooooolyyyyyy crap. I did not realize the quality difference between the stock CSR Elite rim and the Formula rim was going to be so huge. I'm one of the people who doesn't have any issues with the stock rim, but now I'm seriously envious of CSW owners. This is what they've had access to for months. I'd love something like the CSW BMW GT2 wheel rim for the Elite.
- 449
- Toronto
- SignsOfChaos
- SignsOfChaos
LogiForce
Premium
- 4,078
- Groningen, Netherlands
- LogiForce86
- LogiForce
$550/$600 gear emulates $250 gear on PS3. Inverse bang for the buck.
Oh come on. Physically the thing is a lot better in terms of performance, and you know it.
The firmware based deadzone and rattling of those Logitechs just sucks.
If Fanatec would make an SDK and remove the emulation, you would lose compatibility with older games which did not incorporate a Fanatec SDK into their games.
I know you hate Fanatec and have your valid reasons, though please stay a bit reasonable.
Similar threads
